LAUNCH TECH USA 1-877-528-6249 SUPPORT@LAUNCHTECHUSA.COM

sledfreak76 · sledfreak76

Had a 2007 BMW sedan 528 with a dash warning indicator when turning corners. I have a Launch Pad fully updated bought from MAC Tolls for 4000 dollars, what a waste! It would not communicate at all with the BMW auto mode, manual mode, 16 pin, wireless, and wired. A total dissapointment!!!!! I used a SnapO...

diska · diska

Haw to code a new abs moduleon seat ibiza 1997

john millview · john millview

hoping someone can help and guide me how to bleed this x5 im just learning the use of launch x431 diagun and would really appreciate some guidance, no rear brakes after replacing two rearbrake pipes

titine54 · titine54

Hi, I've just buy a Creader VI to use it on my BMW E60 525D. It's correctly connect to the car, read DTC and didn't find anything. But my airbag has a default and it didn't find it. How can I do? Thanks and sorry for my bad "French" english

ifgshooter · ifgshooter

I just replaced a dead fuel pump on an 05 530i. Car now starts & runs great, but the fuel gauge won't read. How do I perform a relearn or reset of the cluster with my Diagun? Is it even possible with the Diagun? Any help would be appreciated.

evounder · evounder

So I have a 2000 x5 and noticed another auto shop installed a new airbag and leveling computer but didnt recode it, do you need to do that and how is that done with the launch?thanks.

joecarparts · joecarparts

Need some help: working on a 2006 750Li with abs light, dsc and parking brake light are on and code 5f20. speedo works fine, but with the my diagun able to read all sensor. left rear not working, replaced sensor, worked , for about 10 minutes. Now the code is back and have no other ideas? Alldata and...

MrGoodWrench · MrGoodWrench

Hi guys, Just found on a 2002 E46, in order to complete a DME to EWS resync, you HAVE TO use the BMW-16 in place of the Super-16. It kept kicking me out completely with no error msg using the Super16 but using the BMW-16 was perfectly fine! Mr. G

john231 · john231

Hello all I was checking a wiper prolem on a 2000 e39 and came up with these two codes under body control. 4B Changer over relay stage 1/2 wiper motor open circuit. 49 Relay for wiper motor open circuit. Can't find any info any where for thes codes. Thx

mrthomas0 · mrthomas0

I have had my euro pro for a week now. i am pretty impressed so far. but i was surprised when yesterday i tried to code a new dsc control unit an 06 e46 m3 and my euro pro stated that this software had not been developed yet. has anyone else tried this? have i downloaded and old version of software?

Jim555 · Jim555

Any one done this?

Volvoartictech · Volvoartictech

Is the X431 capable of coding this module? It seem to pull the info from the old mod just fine but we gat an error when recoding the new module....any help would be great. The module nuber is A13663

CH Autowerks · CH Autowerks

Has any one tryed to code an active steering module on an E64

glensprecision · glensprecision

Does the newest software code the SZL into the DSC. Have to repalce the turnsignal swith (SZL) on a E90 (2006 330i) and I couldn't six months ago and our subsciption expired. Also have another shop with a E63/64 that the battery was unhooked while in storage and now has dash lights on, would it be ab...

Eric · Eric

Just curious if anyone has any positive or negative feedback on doing a coding/recoding with Launch. Recently, (last few BMW versions), have added coding options on the CIP BMW's (E65,E60,E90, etc.). Pretty routine jobs such as replacing occupancy weight sensors require recoding of SRS modules...

AutoLKN · AutoLKN

Using next-to-newest version for BMW (43.50?), the data paramaters: Deviation from ride height, Left Front Deviation from ride height, Right Front Deviation from ride height, Left Rear Deviation from ride height, Right Rear are way off! They are measured in millimeters, and should be from -50...

MrGoodWrench · MrGoodWrench

Hi guys, I got this URL from a friend, all you need is the last 7 digits of the VIN: http://www.realoem.com/bmw/select.do Hope that helps, -Mr. G

aurora · aurora

I have 05 mini that I am unable to clear the body codes for the door locks, I have tried repeatadly to activate the windows and door locks through the scanner,it also wont see the door open/close signal from either door, is this an issue in the sofware. I no for a fact the passenger door latch is working as t...

Rips Wellingsworth III · Rips Wellingsworth III

BMW of N. America sent out a notice dated December 2008 about the failure of the "passenger seat occupant detection mat." When that happens both air bag warning lamp and the passenger air bag "on-off" lamp will illuminate and the passenger side air bag will not deploy. They rec...

theK · theK

Through research I have determined there is a coding requirement between the door module and the door module switch, when you replace the DDM (driver door module, same applies to front passenger side). Currently this is not available in our software for the E60 I was testing, but if you can accomplis...

exopar · exopar

Hi there to all Would like to know how to code a new ABS control module with x431 in a 2000 BMW X5 3.0i. Also this vehicle has 2 conectors 20 (inside the engine bay) and 16 pin (under dahs), which one should be the one for this purposes? Regards Ray

chopstick · chopstick

06 bmw 325i 3.0L came in with air bag light on, scan it and got codes: 93B2 Safety battery terminal. that's what I got from my diagun, but can't find any diagnostic info for those codes in Mitchell on demand. tried googling those codes and nothing came up either. seems like an odd code number. can anyone h...

MrGoodWrench · MrGoodWrench

Hi all, I found some extra time on my hands and decided to do a little write up for everyone who has a X431 and deals with BMW's CBS resets. I will also include a quick blurb on the CBS correction mode which the X431 also has, handy for fixing "other" shops mistakes when they don't know how or can'...

SHAZAM · SHAZAM

Hope this helps us all. see attatched note sent to Award Complaint. The more the all of us here in the U.S. do this, the better the tool will become for the All of us

Eric · Eric

Using a diagun and the 20 pin connector. I tried version 38.80/38.00/36.00 and nothing worked. The 2 options within instrument cluster are service reset and oil reset. Both come back with 'unknown service function'. Tech support, any ideas?

Eric · Eric

Anyone having weird results trying to reset service indicators with the Launch scan tool on chassis such as E38/E39/E46 where you go through body/instrument cluster/service reset? The only way I could get a 2001 7 series (E38) to actually turn off the service reminder light was by changing the tim...

tatsess · tatsess

2002 bmw 325i e46 vin WBAET37452NG81396 anyone know of a way to view readiness monitor status? ...there is nothing in the dme module and generic obd2 software doesn't show anything .i'm using version 38.5 and a super 16 connector... thanks paul

MrGoodWrench · MrGoodWrench

Could not code ABS module with v36.00, tried v38.60 and it coded no problem. TIP: It is ok to turn off the ignition when the software prompts you, it will retain the coding information. Mr. G

MrGoodWrench · Posts: 119 Join date: 2008-03-21

Moved from old forum: 2009 bmw e60 srs codes AuthorMessagetatsess Posts: 119 Join date: 2008-03-21 Subject: 2009 bmw e60 srs codes Wed Jan 13, 2010 4:53 ami have a 2009 5 series e60 ...this car was hit in the left front and a partial upper rail was replaced near the stut tower .. this car was sent to the b...

MrGoodWrench · Posts: 130 Join date: 2009-11-17

Moved from old forum: Resetting/Resyncing LEW module AuthorMessageMrGoodwrench Posts: 130 Join date: 2009-11-17 Subject: Resetting/Resyncing LEW module Tue Dec 01, 2009 2:23 pm Hi all, Just a quick tip for any of you who have to realign or resync a LEW module in a BMW. I found that while you can ac...

Topic		Started By	Replies	Views	Last Post
	Launch PAD ETX431 will not! communicate with 2007 BMW E60/E61 SNAPON VERUS DOES! (Preview) Had a 2007 BMW sedan 528 with a dash warning indicator when turning corners. I have a Launch Pad fully updated bought from MAC Tolls for 4000 dollars, what a waste! It would not communicate at all with the BMW auto mode, manual mode, 16 pin, wireless, and wired. A total dissapointment!!!!! I used a SnapO...	sledfreak76	0	1286	Jun 30, 2013 by sledfreak76
	abs seat ibiza1997 (Preview) Haw to code a new abs moduleon seat ibiza 1997	diska	0	1246	Apr 18, 2013 by diska
	problem abs module bleeding on 04 x5 3.0 d (Preview) hoping someone can help and guide me how to bleed this x5 im just learning the use of launch x431 diagun and would really appreciate some guidance, no rear brakes after replacing two rearbrake pipes	john millview	0	1676	Mar 23, 2013 by john millview
	CREADER VI and BMW E60 (Preview) Hi, I've just buy a Creader VI to use it on my BMW E60 525D. It's correctly connect to the car, read DTC and didn't find anything. But my airbag has a default and it didn't find it. How can I do? Thanks and sorry for my bad "French" english	titine54	2	1905	Jan 3, 2013 by MrGoodWrench
	Fuel Gauge relearn? (Preview) I just replaced a dead fuel pump on an 05 530i. Car now starts & runs great, but the fuel gauge won't read. How do I perform a relearn or reset of the cluster with my Diagun? Is it even possible with the Diagun? Any help would be appreciated.	ifgshooter	1	1309	Jan 3, 2013 by MrGoodWrench
	recoding suspension leveling 2000 x5? (Preview) So I have a 2000 x5 and noticed another auto shop installed a new airbag and leveling computer but didnt recode it, do you need to do that and how is that done with the launch?thanks.	evounder	1	1417	Dec 12, 2012 by evounder
	2006 abs code (Preview) Need some help: working on a 2006 750Li with abs light, dsc and parking brake light are on and code 5f20. speedo works fine, but with the my diagun able to read all sensor. left rear not working, replaced sensor, worked , for about 10 minutes. Now the code is back and have no other ideas? Alldata and...	joecarparts	0	1731	Oct 19, 2012 by joecarparts
	2002 E46 DME to EWS Resync Tip (Preview) Hi guys, Just found on a 2002 E46, in order to complete a DME to EWS resync, you HAVE TO use the BMW-16 in place of the Super-16. It kept kicking me out completely with no error msg using the Super16 but using the BMW-16 was perfectly fine! Mr. G	MrGoodWrench	4	4381	Sep 17, 2012 by AvechuchoAxel
	BMW (Preview) Hello all I was checking a wiper prolem on a 2000 e39 and came up with these two codes under body control. 4B Changer over relay stage 1/2 wiper motor open circuit. 49 Relay for wiper motor open circuit. Can't find any info any where for thes codes. Thx	john231	2	1929	Aug 7, 2012 by john231
	e46 dsc control unit (Preview) I have had my euro pro for a week now. i am pretty impressed so far. but i was surprised when yesterday i tried to code a new dsc control unit an 06 e46 m3 and my euro pro stated that this software had not been developed yet. has anyone else tried this? have i downloaded and old version of software?	mrthomas0	6	2448	Jun 21, 2012 by chopstick
	x3 transfer case oil life reset? (Preview) Any one done this?	Jim555	2	2012	Jun 20, 2012 by MrGoodWrench
	Coding E90 Fuel Pump Control Module (Preview) Is the X431 capable of coding this module? It seem to pull the info from the old mod just fine but we gat an error when recoding the new module....any help would be great. The module nuber is A13663	Volvoartictech	0	1833	May 2, 2012 by Volvoartictech
	E64 Active steering recode (Preview) Has any one tryed to code an active steering module on an E64	CH Autowerks	1	1704	Apr 23, 2012 by MrGoodWrench
	Coding E63 E64 E90 (Preview) Does the newest software code the SZL into the DSC. Have to repalce the turnsignal swith (SZL) on a E90 (2006 330i) and I couldn't six months ago and our subsciption expired. Also have another shop with a E63/64 that the battery was unhooked while in storage and now has dash lights on, would it be ab...	glensprecision	1	2456	Mar 12, 2012 by MrGoodWrench
	Anyone try to code/recode a CIP BMW with Launch? (Preview) Just curious if anyone has any positive or negative feedback on doing a coding/recoding with Launch. Recently, (last few BMW versions), have added coding options on the CIP BMW's (E65,E60,E90, etc.). Pretty routine jobs such as replacing occupancy weight sensors require recoding of SRS modules...	Eric	0	1873	Feb 29, 2012 by Eric
	BMW EHC2 data incorrect (Preview) Using next-to-newest version for BMW (43.50?), the data paramaters: Deviation from ride height, Left Front Deviation from ride height, Right Front Deviation from ride height, Left Rear Deviation from ride height, Right Rear are way off! They are measured in millimeters, and should be from -50...	AutoLKN	0	1608	Aug 15, 2011 by AutoLKN
	Handy tool to ID BMW Chassis Numbers/Vehicles (Preview) Hi guys, I got this URL from a friend, all you need is the last 7 digits of the VIN: http://www.realoem.com/bmw/select.do Hope that helps, -Mr. G	MrGoodWrench	1	1901	Jun 2, 2011 by chopstick
	2005 Mini Cooper Body control Info (Preview) I have 05 mini that I am unable to clear the body codes for the door locks, I have tried repeatadly to activate the windows and door locks through the scanner,it also wont see the door open/close signal from either door, is this an issue in the sofware. I no for a fact the passenger door latch is working as t...	aurora	1	1547	May 25, 2011 by MrGoodWrench
	Airbag light on NO CODES Z4 BMW (Preview) BMW of N. America sent out a notice dated December 2008 about the failure of the "passenger seat occupant detection mat." When that happens both air bag warning lamp and the passenger air bag "on-off" lamp will illuminate and the passenger side air bag will not deploy. They rec...	Rips Wellingsworth III	0	2462	May 12, 2011 by Rips Wellingsworth III
	DDM - coding (Preview) Through research I have determined there is a coding requirement between the door module and the door module switch, when you replace the DDM (driver door module, same applies to front passenger side). Currently this is not available in our software for the E60 I was testing, but if you can accomplis...	theK	0	1556	May 11, 2011 by theK
	How to code a new ABS module in a 2000 X5 (Preview) Hi there to all Would like to know how to code a new ABS control module with x431 in a 2000 BMW X5 3.0i. Also this vehicle has 2 conectors 20 (inside the engine bay) and 16 pin (under dahs), which one should be the one for this purposes? Regards Ray	exopar	7	11442	Apr 6, 2011 by Eric
	bmw airbag codes (Preview) 06 bmw 325i 3.0L came in with air bag light on, scan it and got codes: 93B2 Safety battery terminal. that's what I got from my diagun, but can't find any diagnostic info for those codes in Mitchell on demand. tried googling those codes and nothing came up either. seems like an odd code number. can anyone h...	chopstick	2	5470	Feb 23, 2011 by chopstick
	How-to: BMW 2002+ Condition Based Service (CBS) Reset/CBS Correction Mode (Preview) Hi all, I found some extra time on my hands and decided to do a little write up for everyone who has a X431 and deals with BMW's CBS resets. I will also include a quick blurb on the CBS correction mode which the X431 also has, handy for fixing "other" shops mistakes when they don't know how or can'...	MrGoodWrench	1	3487	Oct 22, 2010 by coyote
	LEW coding request sent to Launch (Preview) Hope this helps us all. see attatched note sent to Award Complaint. The more the all of us here in the U.S. do this, the better the tool will become for the All of us	SHAZAM	11	2793	Sep 17, 2010 by coyote
	Problem with service reset on 1997 - E38 (7 series) (Preview) Using a diagun and the 20 pin connector. I tried version 38.80/38.00/36.00 and nothing worked. The 2 options within instrument cluster are service reset and oil reset. Both come back with 'unknown service function'. Tech support, any ideas?	Eric	0	1256	Jul 28, 2010 by Eric
	E38 service reset via scan tool (Preview) Anyone having weird results trying to reset service indicators with the Launch scan tool on chassis such as E38/E39/E46 where you go through body/instrument cluster/service reset? The only way I could get a 2001 7 series (E38) to actually turn off the service reminder light was by changing the tim...	Eric	2	1673	Jul 22, 2010 by Eric
	2002 bmw 325i e46 readiness codes (Preview) 2002 bmw 325i e46 vin WBAET37452NG81396 anyone know of a way to view readiness monitor status? ...there is nothing in the dme module and generic obd2 software doesn't show anything .i'm using version 38.5 and a super 16 connector... thanks paul	tatsess	1	1747	Apr 24, 2010 by edmond
	2001 530i ABS Module Coding (Preview) Could not code ABS module with v36.00, tried v38.60 and it coded no problem. TIP: It is ok to turn off the ignition when the software prompts you, it will retain the coding information. Mr. G	MrGoodWrench	1	1513	Apr 21, 2010 by coyote
	2009 BMW E60 SRS Codes (Moved from old forum) (Preview) Moved from old forum: 2009 bmw e60 srs codes AuthorMessagetatsess Posts: 119 Join date: 2008-03-21 Subject: 2009 bmw e60 srs codes Wed Jan 13, 2010 4:53 ami have a 2009 5 series e60 ...this car was hit in the left front and a partial upper rail was replaced near the stut tower .. this car was sent to the b...	MrGoodWrench	0	5898	Mar 2, 2010 by MrGoodWrench
	Resetting/Resyncing LEW module (Moved from old forum) (Preview) Moved from old forum: Resetting/Resyncing LEW module AuthorMessageMrGoodwrench Posts: 130 Join date: 2009-11-17 Subject: Resetting/Resyncing LEW module Tue Dec 01, 2009 2:23 pm Hi all, Just a quick tip for any of you who have to realign or resync a LEW module in a BMW. I found that while you can ac...	MrGoodWrench	0	1334	Mar 2, 2010 by MrGoodWrench
«First < 1 2 3 > Last» \| Page of 3 sorted by